For home improvement, the toilet is essential. To choose a suitable toilet, you should first know what is more important.
1. Weight
The heavier the toilet, the better. The average toilet weighs about 50 pounds, and a good toilet weighs about 100 pounds. The heavy-weight toilet has a high density and a relatively high quality. A simple way to test the weight of the toilet: pick up the lid of the water tank with both hands, and you can weigh its weight.
Second, the water outlet: a best sewage outlet
It is best to have one sewage hole at the bottom of the toilet. At present, many brands have 2-3 sewage holes (according to different calibers), but the more sewage holes affect the impact. The water outlet of the toilet is divided into the down drain and the horizontal drain. The distance between the center of the drain and the wall behind the water tank should be measured. Buy the toilet of the same model to "seed to the seat, otherwise the toilet cannot be installed. It is equal to the height of the horizontal drain, and it is better to be slightly higher to ensure the smooth flow of water. 30 cm is the mid-flush toilet: 20-25 cm is the rear flush toilet; the distance is more than 40 cm is the front flush toilet. Mistakes make it difficult to launch.
3. Glaze: smooth and non-foaming, with the best color saturation
Pay attention to the glaze of the toilet. The glaze of a good-quality toilet should be smooth and smooth without blistering and saturated in color. After inspecting the glaze on the outer surface, you should also touch the drain of the toilet. If it is rough, it will easily cause hangover in the future.
4. Caliber: large glaze on the surface
Large-diameter sewage pipes with glaze on the inner surface are not easy to hang dirty, the sewage is fast and powerful, and effectively prevents clogging. The test method is to put the entire hand into the toilet mouth, and it is generally best to have a palm capacity.
5. Water tank: the higher the height, the greater the impulse
In addition to the obvious sound of dripping sound, the leak of the toilet tank is generally not easy to detect. The simple check method is to add blue ink into the toilet tank. After mixing, see if there is blue water flowing out of the toilet outlet. Leaking place. As a reminder, it is better to choose a tank with a higher height so that the impulse is very good. (Note: The flush volume below 6 liters can be classified as a water-saving toilet.)
Six, water: the button sound should be clear
The water piece directly determines the service life of the toilet. The quality of the water parts of brand toilets and ordinary toilets is very different, because almost every family has experienced the pain of water tanks, so when choosing a toilet, do n’t ignore the water part. The identification method is to hear the sound of the button. A clear voice is the best.
7. Material of toilet lid: Engineering plastic is more expensive than ordinary plastic, but the human body feels much more comfortable with engineering plastic, and the cover is not easy to break.
8. Flushing: the best way to quickly discharge sewage and save water
From a practical point of view, the toilet should first have the basic function of flushing thoroughly. Therefore, the flushing method is very important. The flushing water of the toilet is the direct flushing type, the rotating siphon type, the vortex siphon type, and the jet siphon type. Pay attention to choose different drainage methods: the toilet press water can be divided into "flush", "siphon flush" and "siphon vortex" and so on. The flushing type and siphon flushing type water injection volume is about 6 liters, and the sewage discharge ability is strong, but the sound is loud when flushing; while the vortex type has a large water consumption at a time, but it has a good mute effect. Consumers may wish to try the direct flush siphonic toilet in the Minxiang market. It has the advantages of direct flush and siphon, which can quickly flush dirt and save water.
PCD Cutting Tool Blanks(PCD Disc)
BOHONG has world-class production facilities for PCD cutting tool blanks. BOHONG PCD is widely used for machining non-ferrous metals and alloys, such as aluminum, copper, aluminum/gray iron composites, as well as nonmetallic materials such as wood, chipboard, ceramics, plastic, rubber etc, where high abrasion resistance and good surface finish are required.
Pcd Cutting Tool Diamond Tool,Pcd Cutting Tool Blank For Insert,Pcd End Mill Tools Cutter,Pcd Solid Wood Cutting Tools
Henan Bohong New Material Co., Ltd , https://www.bohongpcd.com