| Home>Bearing knowledge> Due to improper hygiene, "the cause of the disease is a big inventory" |
Due to improper hygiene, "the cause of the disease is a big inventory"
Source: China Bearing Network Time: 2014-05-27
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
When large particles of alloy blocks or flakes are found in the oil filter element and the initiating oil sump; the shaft and the bearing bush have been severely damaged; it is necessary to stop the inspection and correction immediately; if it is continuously used, more parts will be damaged. .
The reason for the entry of larger particles is that the parts are not cleaned when the device is installed; for example, the metal chips that occur when processing the inner hole of the connecting rod bushing remain in the oil passage of the connecting rod, the cutting or sediment is stuck in the parts and the oil passage, and the cutting is not completed before the device. Or the machining burrs of the machined parts associated with the moving surface are not removed, the foreign objects with larger particles sticking to the bearing bushings or the outer surface of the shaft are damaged. These images are very serious for the damage of the bearing pads. Carefully clean up and view the device.
The smoothing effect and heat dissipation of the residual smooth oil can not meet the demand; the bearing and the shaft wear are aggravated; the alloy with excessive surface temperature is melted and damaged, and the oil of the residual smooth oil is more blocked. The smooth oil rich in impurities directly enters the moving surface without filtering; further accelerates the damage of the shaft and the bearing bush. Therefore, when purchasing and replacing the smooth oil, the quality of the smooth oil must be strictly controlled according to the rules; the smooth oil is selected according to the rules.
2. Do not move foreign objects to damage the shaft and bearing bush:
There is a large foreign object between the bearing bush and the inner wall of the tile device; the movement of the bearing bush will be convex; when the shaft is working; the abnormal wear will start from the bump; and expand to the periphery; form the shaft and Early damage of the bearing bush, if there is a large foreign object between the moving surface of the bearing bush and the shaft; the device will be embedded in the alloy layer of the bearing bush after the device; when working, the bearing shaft will also damage the bearing bush, the shaft and the tile and the device hole, etc. If the associated part has bumps and bumps, it will damage or damage the shaft and the tile.
Reasons for occurrence and avoidance: Oxidation or sedimentation of shaft, bearing bush, bushing hole (body, connecting rod); careful inspection of the device before the device; especially the oil passage and the inner lumen of the tubing, it is necessary to stay away from the device. In places where dust is flying and debris is splashed, the equipment used should be clean and hygienic; and the necessary protection measures should be adopted; avoid re-contamination; the smooth oil used in the installation should be hygienic; avoid dust mixing, shafts and bushings and bushing holes. The registration and installation; to ensure that it does not touch any metal objects and must not have any touch operations.
3. Wear of small particle foreign matter on bearing pad formation:
When the oil filter element is in the oil drain plug of the engine oil bottom; the first few oils flowing out of the oil; the naked eye can be directly seen and more alloy powder; the bearing bush is now worn. This is due to the small size The impurities of the particles enter the movement of the bearing layer of the bearing shell; although the bearing bush does not form severe damage; however, such an image continues to develop; not only the early damage of the bearing bush; the shaft is also severely damaged; therefore, it is necessary to rely on the disease The reason for the timely removal; avoid the damage of the formed parts. The service life of the starter bush after the fault is removed cannot be calculated according to the normal wear time; because the abnormal wear of a small particle is equivalent to the normal wear of the machine for 2500 hours. .
The reason for the entry of fine particles is as follows: First, the filter function of the air filter is poor or the sealing of the air intake system is not good; the pipelines and joints of the intake system should be checked; whether there is a break or looseness; whether the filter element is loose or not, Whether the paper core is broken or not. Whether it is repair or protection is the protection of the entire air intake system is very important; it is necessary to ensure reliability. Second, after the smooth oil is contaminated, participate in the launching machine or the oil and the filter element is used for a long time. Blocked; so that the smooth outer surface of the oil does not filter directly into the filter element. Third, the fuel supply is too large for incineration, nozzle leakage; the formation of fuel into the crankcase; together with some impurities into the crankcase with fuel and The oil mixes together to reduce the smoothing effect. Therefore, the launching machine should pay attention to investigating the smoke exhaustion and working condition of the initiator in the application; if there is an abnormality, it should be checked and corrected in time to correct or replace it. Fourth, when the initiator is assembled; the internal parts are sanitized. Degree difference. When repairing and protecting the initiator; must pay attention to the hygiene of the parts; the device should pay attention to avoid re-contamination; ensure the internal hygiene after the device.
No matter what kind of reason; it is necessary to replace the engine oil and the filter element after sweeping the fault. The repaired starter starts the work for two hours to stop the work for inspection; there is no alloy powder in the oil; However, it is necessary to pay attention to the investigation in the first few days of application; after 60 to 120 hours of work, it is confirmed that the abnormal wear is completely removed; and the oil is replaced; the initiator can be put into normal use. If abnormal wear is continued, it is necessary Aborting the application for crash viewing and correction.
Recommend to friends comments close window
| Bearing related knowledge |
| Bearing rear code name clarification (1) Analysis of the clearance of rolling bearings NTN rolling bearing problems, several typical reasons for the characteristics of four-point contact ball bearings, "spheroidal roller bearing timing view" has a coup |
This article links to http://
Please indicate the bearing network http://
Previous:How to determine whether the damaged bearing can be used in the next section: New technology for anti-rust between fine imported bearings
UV Birch Plywood,UV Prefinished Plywood,UV Coated Birch Plywood,UV Finished Birch Plywood
LINYI JIUHENG IMP&EXP CO.,LTD , https://www.jiuhengwood.com