Nowadays, gypsum board is more and more widely used in home decoration. Not only can it make a high-grade suspended ceiling, but also can be made into a very practical partition. So, what is the practice of gypsum board partition walls ? What specifications of gypsum board are used for partition walls? Next, the editor will talk to you about the practice of gypsum board partition walls .
1. What kind of gypsum board is used for partition wall
1. There are currently two types of gypsum board on the market. One is a calcium-silica gypsum board specially used for ceilings. The standard specifications are 600mm * 600mm * 14mm or 600mm * 1200mm; Paper surface gypsum board, standard thickness specifications 9.5mm, 12mm, 15mm, length 2400 * 1200mm, etc.
2. The affinity of ordinary paper-faced gypsum board and putty is very high. After shaving the putty powder, the surface is very smooth. As long as it is not illuminated by strong light, there will not be too much reflection. In addition, latex paint can also be applied to this type of gypsum board, and the decorative effect is not bad. In terms of functionality, it can also be divided into moisture-resistant and fire-resistant plates.
2. The practice of gypsum board partition
1. Before the construction of the gypsum board, the specific location of the wall and the door opening must be marked according to the design requirements, so that the subsequent construction can be facilitated.
2. The quality, specifications and attributes of the gypsum board must meet the basic requirements of the construction quality of the partition wall.
3. Before the official start of construction, check the arrangement of all pipelines related to the wall and confirm that it will not interfere with the line before starting construction.
4. Before installing the keel, put 5mm of rubber on the periphery of the gypsum board, the width is consistent with the keel.
5. The keel along the top and the ground area is preferably fixed with shot nails, so that the operation is more firm, and the distance between each shot nail should be less than 600mm.
6. The vertical keel spacing is generally set to about 400mm, and the spacing is maintained from one end of the wall to the other end. When the last one is greater than the pre-designed spacing, an additional one is required for reinforcement. The three ends of the three tests also need to be reinforced with a keel.
7. When going up the main keel, add a gap of not more than half of the width of the gypsum board, which means insert the edge keel at the upper and lower ends at a distance of five millimeters, and fix it with a nail on the vertical keel against the wall and the column The distance between nails is not more than 900mm.
Summary of the article: The above is all about the practice of gypsum board partition wall and what specifications of gypsum board used for partition wall. Gypsum board partition is a very economical way of partitioning. It can be used in large areas such as living rooms and study rooms. With a little decoration, the effect is very beautiful!
What, the decoration still uses his own money? ! The Qi family is decorated in installments, with an ultra-low annual interest rate of 3.55% and a maximum loan of 1 million. Apply now to enjoy the discount
If you are interested in brand cooperation, content cooperation, and advertising of this website, please send an email to :.
Gypsum board partition
Recessed LED Downlight with built-in Microwave Motion Sensor
| Model | AM-6.0GY |
| Luminous flux | 800~900lm |
| Luminous Efficacy | >80lm/W |
| Colour Rendering index | 80 |
| Beam Angle | 140° |
| Light Decay | <30% over 10,000 hours |
| Rated Lifespan | >30,000 hours |
| Power consumption | 10 watts |
| Input voltage / Frequency | 80-260vac 50-60HZ |
| Reflector / Diffuser | Frosted diffuser |
| Operating Environment | -20°c~+50°c |
| Dimensions | Φ193*77mm |
| Hole Cut Size | Φ160~Φ180mm |
| LED Source | 56pcs SMD2835 |
| Working mode | ON/OFF or Full/Dim |
| Sensor Range | 180*360 degree |
| Sensor Distance | 6-8m Radius |
| Delay Time |
18-25s |
Sensor Led Down Light,Recessed Led Down Light,Led Ceiling Down Light,Smart Down Light
JIANGMEN MOSCOT OPTOELECTRONIC TECHNOLOGY CO.,LTD. , https://www.jmsensorsled.com